Common Frigidaire dishwasher problems
Thorough frigidaire dishwasher repair starts with the way these built-ins are made — a standard FFID or FDSP, a Gallery FGID or GDPH, or a Professional FPID, each built around the OrbitClean Spray Arm, DishSense soil sensing, MaxBoost or EvenDry drying, and on the Gallery and Professional tiers a stainless tub. Modern Frigidaire dishwashers use lowercase i-codes shown as a flashing two-digit set, plus a few two-letter status codes; older models without a display blink the cycle light instead. The complaints we see most are a poor or no fill (i10), standing water from a drain restriction (i20, i40, or iF0 — Frigidaire treats these as the same condition), a leak that trips the flood float (i30), a wash or drain motor fault (i50), and water that will not heat (i60). The filters, the OrbitClean spray arms, the drain pump, the inlet valve, the door latch, and the heating element all wear and clog with use.
Our Frigidaire dishwasher repair process
As an independent, third-party service our experienced technicians begin every Frigidaire dishwasher repair by confirming the model and reading any i-code before parts are touched. An i10 sends the technician to the supply, the inlet screen, and the water inlet valve; an i20, i40, or iF0 to the filter, glass trap, sump, and drain hose, since these three codes share the same drain-restriction cause; an i30 to finding and fixing the leak before the float can be cleared; an i50 to the wash and drain motor; and an i60 to the heating element and thermistor. A CL is simply a door not latched, while a recurring PF means the house supply is checked rather than dismissed. We fit genuine OEM parts from trusted parts suppliers, and every visit is backed by a 30-day labor warranty on the workmanship. Most repairs are completed in a single trip, and you can book a dishwasher repair online at any time, with a clear quote before work begins and a total that depends on the diagnosis rather than a fixed price.
Frigidaire dishwasher models we service
We service the Frigidaire dishwasher lineup across all three tiers. Standard models include the FFID2426TS, FFCD2418US, FDPC4221AS, and the top-control FDSP4501AS with a stainless tub and third rack; Gallery models include the FGID2466QF, FGID2476SF, FGIP2468UF, FGCD2444SA, GDPH4515AF, GDSH4715AF, GDPP4515AF, and GDPP4517AF; and Professional models include the FPID2498SF and FPID2497RF. We also handle discontinued models as repair-lookup work, since the pump, valve, and control parts stay serviceable. These dishwashers carry the OrbitClean or Dual OrbitClean spray arm, DishSense, MaxBoost Dry, EvenDry or SaharaDry, BladeSpray, the SpaceWise rack, and a 34-minute Quick Wash on many builds. Our model directory lists the inlet valves, drain pumps, wash motors, heating elements, thermistors, door latches, and control boards matched to each specific build so the correct genuine OEM part is sourced the first time. Because the Gallery and Professional tiers use a stainless tub while the standard FFID and FDPC builds use a plastic tub, the right replacement seal, sump, and filter assembly differ between them, so we confirm the tub type before any part is ordered and the fit is correct on the first visit.
Error codes and diagnostics
A Frigidaire dishwasher is diagnosed by reading its i-code and confirming the named part. i10 is a low or slow fill; i20, i40, and iF0 are the same drain-restriction condition; i30 is a leak or tripped flood float; i50 is a wash or drain motor fault; i60 is a water-heating error; and iC0 is a control-communication loss. The two-letter status codes include ER (stuck touchpad key), CE (configuration error), CL (door not latched), PF (power failure), HO (heat delay, which is normal), LO (rinse aid low), rA (rinse-aid switch), UO (vent fault), and tu (turbidity sensor). Most clear with START/CANCEL or a five-minute power-off at the breaker, but a code that returns means the named component has failed. Frigidaire uses these i-codes, not another brand’s F-then-E format. Look up what each one means on our dishwasher error-code guides.
Service areas
Our specialist technicians cover all 50 states and the District of Columbia plus 40-plus metro areas, with a standard 24-48 hour response and same-day visits where availability allows. A Frigidaire dishwasher built around the OrbitClean Spray Arm and DishSense deserves a technician who clears the filter and drain path properly and confirms each i-code at the part. Every visit is handled by a skilled technician who carries the diagnostic tools and the genuine OEM parts most likely needed, so the fault is identified and, wherever possible, fixed on the first trip. Full specifications and the current dishwasher lineup are published by the manufacturer at frigidaire.com. Find your area on our service locations page, browse step-by-step help in our repair guides, or book any service through the scheduling page.